Flowright Flowserve Pumps


FLOWSERVE CPX SINGLE STAGE CHEMICAL PROCESS PUMPS

“FLOWSERVE” Pumps are available with Investment cast twisted vane impeller of duplex SS (CD4MCu) for better erosion capability.

Advanced 45 degree conical shaped seal chamber with integral vortex flow modifiers controls vapour build-up and ensures adequate flow conditions to remove heat effectively. It also increases the mechanical seal life. It incorporates many different seal designs with sufficientradial clearance.


Brochure

Heavy Duty Pump End Drive End Bearings Selected for long life and reliability.

Heavy duty casing with integral foot and multiribbed discharge provides superior resistance to pipe loads and improves Reliability.

External Three Bolt Rotor Adjustment allows impeller clearances to be reset at site, thereby restoring head and efficiency.

Back Pull-out Design allow removal of rotating element without removing casing, piping or motor.



FLOWSERVE - SIHI ZTND

FLOWSERVE - SIHI's ZTND Line isa specialty line of pumps specifi- cally designed to handle hot thermal fluids. Pumps are available in 24 models with only two shaft sizes. SIHI's ZTND designs use a dual heat restricting design allowing the pumping of thermal fluids to 650+ °F. Engineered to allow ambient air cooling while minimizing thermal transfer along the shaft, they offer safety and efficiency, eliminating any need for liquid cooling through their operating range. Shaft sealing is provided by either a set of v-ring lip seals (to minimize the possibility of catastrophic shaft seal failures) or single non-cooled mechanical seal.

Features ZTND:

  • Self-Cooling
  • Unique Shaft Sealing
  • Back Pull Out Design

Technical Data:

  • Capacity: 2600 GPM
  • Total Head: 296 Ft.
  • Temperature: 662°F (max.)

Material: Ductile iron
Note: Applications exceeding these ranges, please consult Factory

Industries and Applications:
• Chemical • Food • Rubber & Plastic • Paper • Laundry



FLOWSERVE MAG DRIVEN PUMPS

FLOWSERVE - INNOMAG TB-MAG FLUOROPOLYMER- LINED,MAGNETIC DRIVE, ISO OR ASME (ANSI) CHEMICAL PROCESS PUMP

The INNOMAG TB-MAG sets a new benchmark for magnetic drive pump value and performance. Compliant with ASME B73.3 or ISO 2858/15783 standards, this versatile pump is engineered to provide low total cost of ownership and exceptional leakage protection in extremely corrosive and environmentally critical applications, including “clean floor” initiatives.

While the TB-MAG boasts many innovative design elements, the key to its proven performance is its revolutionary dynamic thrust balancing system. This cleverly engineered system eliminates the need for thrust bearingsand results in highly efficient operation with outstanding reliability, even in applications containing solids.

  • Dynamic Thrust Balancing System eliminates the need for thrust bearings.
  • Pump efficiency, reliability and longevity are improved, while operating costs are reduced.
  • Pure ETFE Casing Liner is vacuum rated and has a minimum thickness of 3 mm (0.125 in).
  • One-piece ETFE Impeller and Inner Magnet Assembly ensures maximum torque transmission, simplifies maintenance and eliminates balancing.
  • Enclosed impeller with unobstructed eye delivers high efficiency and low NPSHR.
  • Double-sealed Inner Magnets offer unmatched resistance to corrosive permeation by sheathing the magnets in 316L stainless steel before they are injection molded into the impeller assembly.
  • One-piece Composite Containment Shell consists of aramid and carbon fiber reinforced ETFE for optimal leakage protection and corrosion resistance.
  • Composite construction means zero eddy current losses for maximum efficiency.
  • Stationary Cantilevered Pump Shaft is oversized to handle all radial loads while maximizing flow and minimizing NPSHR.
  • Parts Interchangeability among the available sizes reduces inventory costs and eases maintenance.
  • Superior solid handling capabilities allowreliable performance up to 30% solids content of 0,13 mm.